DMZ Key Map

MW4 Best PC Settings for DMZ (FPS & Visibility)

Last verified · Game build: launch

Start from the preset the game picks for your PC. Then turn off V-Sync, motion blur and ray tracing, turn on Reflex or Anti-Lag, and use DLSS, FSR or XeSS. Choose Competitive, Balanced or Low below and check the result with the in-game Benchmark Tool.

Community consensus — verify with the in-game Benchmark tool. Map

Display

Display Mode

Fullscreen Exclusive

Exclusive fullscreen gives the game full control of refresh rate and latency.

Reported

V-Sync

Off

V-Sync adds input lag; use G-Sync/FreeSync instead if you have it.

Reported

NVIDIA Reflex / AMD Anti-Lag

On

Lowers input latency at almost no FPS cost.

Reported

Quality

Upscaling (DLSS / FSR)

Quality

Upscaling is the cheapest way to gain frames; Quality keeps the image clean at 1080p and 1440p.

Reported

Ray Tracing

Off

Heavy on the GPU and not needed to spot enemies.

Reported

Shadow Quality

Low

One of the biggest FPS costs; low shadows also make dark rooms less murky.

Reported

Volumetric Quality

Low

Fog and light shafts cost frames and can hide players.

Reported

Motion Blur / Depth of Field / Film Grain

Off

All three blur or add noise to the image.

Reported

Texture Resolution

By VRAM (High on 8GB+)

Textures barely cost FPS if you have the VRAM, and help you read details.

Reported

VRAM Scale Target

80–85

Leaves headroom so the game doesn't stutter when VRAM fills up.

Reported

View

Field of View

100–110

Wider view helps awareness in a big map; go wider only if your FPS holds.

Reported

PC requirements

  • Activision targets 90 FPS in multiplayer on High settings at the Recommended specs. It gives no separate figure for DMZ.
  • TPM 2.0 and Secure Boot must be on, and you need an SSD with 115 GB free.
  • Recommended: Ryzen 5 3600 or Core i7-8700, 16 GB RAM, Radeon RX 6600 XT, GeForce RTX 3060 Ti or Arc B580 (8 GB VRAM), Windows 11.
  • Minimum: Ryzen 5 1400 or Core i5-6600, 8 GB RAM, Radeon RX 470, GeForce GTX 970 or GTX 1060, or Arc A580 (3 GB VRAM).
  • Intel Arc cards need Resizable BAR switched on.

Which profile should I use?

ProfileFor
CompetitiveStrong PCs: maximum frame rate and visibility
BalancedMid-range PCs: a steady frame rate that still looks good
LowMinimum-spec PCs and laptops: playable and stable first

Upscalers

The game offers NVIDIA DLSS 4.5, AMD FSR Redstone and Intel XeSS 3. Filmic SMAA T2X is the default, but it only smooths jagged edges and does not add frames. Pick the upscaler that matches your GPU, and use the Sharpness slider if the image looks soft.

Use the Benchmark Tool

The built-in Benchmark Tool plays a simulated match and reports your average FPS, CPU and GPU load and input latency, then suggests settings. Run it after every change; the values here are a starting point, not measured results.

DMZ-specific tips

Hajin has very dark interiors, such as the casino and the underground mall. NVG and HDR brightness advice for DMZ will be added after launch, once we've tested it ourselves. Meanwhile, see the map guide for areas where you'll want NVGs.

FAQ

What are the best PC settings for FPS in MW4 DMZ?

Use an upscaler (DLSS, FSR or XeSS), turn off ray tracing, V-Sync and motion blur, and lower shadows, particles and screen-space effects first. Keep textures as high as your VRAM allows.

Does Modern Warfare 4 need TPM 2.0 and Secure Boot?

Yes. Both must be enabled on PC.

What FPS can I expect at Recommended specs?

Activision targets 90 FPS in multiplayer on High settings at Recommended specs. It has not given a DMZ figure.

Should I use frame generation in DMZ?

We suggest leaving it off for fights, because it adds input latency. It can smooth things out in calmer moments if you already get around 60 FPS without it.

Sources